You have no items in your shopping cart.
Finally a solution to the problem of esthetically unattractive crowns and bridges! The new Revitalize supplemental Kit has been designed to enable you to place LUMINEERS over clinically adequate crowns and bridges that are no longer attractive to your patients. This kit contains all the bonding materials necessary to bond to metal, porcelain and composite resin. Its proven chemistry for crown and bridge repair and resurfacing will allow you to bring new vitality to existing restorations. In the past, patient's thought "not yet, it doesn't look bad enough" because they remember the painful process of placing crowns and bridges. Your patients can renew their appearance painlessly with the Revitalize Supplemental Kit, combined with clinically proven LUMINEERS BY CERINATE.
BONDING PORCELAIN TO PORCELAIN
1. Sandblast (microetch) to roughen the porcelain surface.
2. Apply Porcelock® Porcelain Etchant (Kit No. 402060) to the
porcelain surface for 2-3 minutes; rinse and dry. Avoid soft
tissue contact.
3. Apply Porcelain Conditioner to the porcelain surface for
30 seconds; rinse and dry.
4. Apply Cerinate Prime® (Kit No. 1399) and gently air dry.
5. Apply Tenure® A and B.
6. Use the Cerinate® Shade Modifier and TetraPaque® Opaquer (a
thin layer) on the metal to mask discoloration, if needed. (See For
Gumline Discoloration section).
7. Apply Ultra-Bond® Resin Cement inside Lumineers™ and place
Lumineers on the tooth surface.
8. Light-cure for 1-2 seconds using the Ceri-Taper™ 2 mm or 4 mm
tacking tip and the Sapphire™ Plasma Arc Curing Light. Remove
excess Ultra-Bond Resin Cement from the margins by using a
soft brush coated with Tenure S. Using a 9mm tip and the
Sapphire PAC light, completely cure all Lumineers, exposing
each surface for 5 seconds.
9. Maximum bonding occurs in 24 hours. Final finishing is to be
performed at next visit.
10. Finishing—Adjust the occlusion and perform a routine finish on
the margins.
FINISHING
1. Use a Schure 349 instrument (Part No. N349) to remove excess
Ultra-Bond Resin Cement. This instrument will not harm the
porcelain surface.
2. Use fluted burs and fine-tapered diamonds to finish margins.
3. Adjust occlusion.
4. Use CeriSaw (Kit No. 031336500) to open contacts and
CeriSander (Kit No. 031337500) to finish interproximal surfaces.
FOR GUMLINE DISCOLORATION
1. Remove all visible metal collars with one-half round diamond bur
and the use of 4X (Power) Cerinate Magnification System.
2. Continue with steps 2-10 under Bonding portion of instructions.
SHADE MODIFICATION
For additional shades, we recommend the Shade Modification II
System by Cerinate (Kit No. 033909900).
1. Sandblast (microetch) to roughen the porcelain surface.
2. Apply Porcelock® Porcelain Etchant (Kit No. 402060) to the
porcelain surface for 2-3 minutes; rinse and dry. Avoid soft
tissue contact.
3. Apply Porcelain Conditioner to the porcelain surface for
30 seconds; rinse and dry.
4. Apply Cerinate Prime® (Kit No. 1399) and gently air dry.
5. Apply Tenure® A and B.
6. Use the Cerinate® Shade Modifier and TetraPaque® Opaquer (a
thin layer) on the metal to mask discoloration, if needed. (See For
Gumline Discoloration section).
7. Apply Ultra-Bond® Resin Cement inside Lumineers™ and place
Lumineers on the tooth surface.
8. Light-cure for 1-2 seconds using the Ceri-Taper™ 2 mm or 4 mm
tacking tip and the Sapphire™ Plasma Arc Curing Light. Remove
excess Ultra-Bond Resin Cement from the margins by using a
soft brush coated with Tenure S. Using a 9mm tip and the
Sapphire PAC light, completely cure all Lumineers, exposing
each surface for 5 seconds.
9. Maximum bonding occurs in 24 hours. Final finishing is to be
performed at next visit.
10. Finishing—Adjust the occlusion and perform a routine finish on
the margins.
FINISHING
1. Use a Schure 349 instrument (Part No. N349) to remove excess
Ultra-Bond Resin Cement. This instrument will not harm the
porcelain surface.
2. Use fluted burs and fine-tapered diamonds to finish margins.
3. Adjust occlusion.
4. Use CeriSaw (Kit No. 031336500) to open contacts and
CeriSander (Kit No. 031337500) to finish interproximal surfaces.
FOR GUMLINE DISCOLORATION
1. Remove all visible metal collars with one-half round diamond bur
and the use of 4X (Power) Cerinate Magnification System.
2. Continue with steps 2-10 under Bonding portion of instructions.
SHADE MODIFICATION
For additional shades, we recommend the Shade Modification II
System by Cerinate (Kit No. 033909900).
Each Kit Contains:
* Paint-On-Dental Dam Syringe – 3 mL
* PorceLock Solution Syringe – 1.75 mL
* Shade Modifier by Cerinate, White – 1 g
* TetraPaque Pink – 1 g
* Syringe tips 18G – 6 pc
* Syringe tips 20G – 10 pc
* Mixing pad
* Rule of 55 Chart
* Paint-On-Dental Dam Syringe – 3 mL
* PorceLock Solution Syringe – 1.75 mL
* Shade Modifier by Cerinate, White – 1 g
* TetraPaque Pink – 1 g
* Syringe tips 18G – 6 pc
* Syringe tips 20G – 10 pc
* Mixing pad
* Rule of 55 Chart
What about the Revitalize Kit enables me to bond porcelain to porcelain?
With the Revitalize kit, in conjunction with LUMINEERS, your patients can renew their appearance painlessly. The Revitalize kit includes materials that will prepare existing crowns and bridges to accept the LUMINEERS bonding process. Revitalize Etchant (Porcelock) is a hydrofluoric acid solution that will etch the existing porcelain. There are also agents included in the kit that will mask out gray margins. The key to this technique is the strength of the LUMINEERS and Revitalize Cement. These two products work together with Tenure to provide an extremely thin and strong restoration that is changing the dental industry!
If I do not have the Revitalize Kit, but I have Ultra-Bond and Tenure, can I still bond porcelain to porcelain?
You can place LUMINEERS over clinically adequate crowns and bridges using Ultra-Bond and Tenure. However, there are additional steps required to prepare the existing porcelain surface. These additional steps are critical in achieving a strong bond, and the Revitalize Kit was specifically created to include the materials required. Please contact your Den-Mat Account Executive for further information.
What are the benefits of placing LUMINEERS over existing crowns or bridges versus replacing them?
Millions of people have bridgework or crowns that are not esthetically pleasing, but are hesitant to update their smile due to fear of pain. Revitalize is the solution! No anesthetics, temporaries, or removal of old restoration work is necessary. Patients are receptive to this non-invasive alternative.
Once I place LUMINEERS over existing porcelain, is the procedure reversible?
When bonding LUMINEERS to existing teeth, the procedure is often reversible due to the no-prep technique. However, when placing LUMINEERS over existing crowns and bridges it is necessary to sandblast and etch the porcelain. This allows the strongest bond possible. This technique will remove the glaze from the existing crown or bridge, and therefore isn’t reversible.
With the Revitalize kit, in conjunction with LUMINEERS, your patients can renew their appearance painlessly. The Revitalize kit includes materials that will prepare existing crowns and bridges to accept the LUMINEERS bonding process. Revitalize Etchant (Porcelock) is a hydrofluoric acid solution that will etch the existing porcelain. There are also agents included in the kit that will mask out gray margins. The key to this technique is the strength of the LUMINEERS and Revitalize Cement. These two products work together with Tenure to provide an extremely thin and strong restoration that is changing the dental industry!
If I do not have the Revitalize Kit, but I have Ultra-Bond and Tenure, can I still bond porcelain to porcelain?
You can place LUMINEERS over clinically adequate crowns and bridges using Ultra-Bond and Tenure. However, there are additional steps required to prepare the existing porcelain surface. These additional steps are critical in achieving a strong bond, and the Revitalize Kit was specifically created to include the materials required. Please contact your Den-Mat Account Executive for further information.
What are the benefits of placing LUMINEERS over existing crowns or bridges versus replacing them?
Millions of people have bridgework or crowns that are not esthetically pleasing, but are hesitant to update their smile due to fear of pain. Revitalize is the solution! No anesthetics, temporaries, or removal of old restoration work is necessary. Patients are receptive to this non-invasive alternative.
Once I place LUMINEERS over existing porcelain, is the procedure reversible?
When bonding LUMINEERS to existing teeth, the procedure is often reversible due to the no-prep technique. However, when placing LUMINEERS over existing crowns and bridges it is necessary to sandblast and etch the porcelain. This allows the strongest bond possible. This technique will remove the glaze from the existing crown or bridge, and therefore isn’t reversible.
"There are those times that my patients are no longer satisfied with their existing crown and bridge restorations. It might be a discolored, dark margin due to recession, or the color doesn't match anymore. I no longer have to replace everything. With
"I have never seen any restoration look so perfect and natural! I would have done this years ago had I known about Revitalize."
" It turned out wonderful and Im not only pleased, but I have next case already booked with Cerinate Studios."
"I received info on the Revitalize Kit and wanted to know how I could get them free. Was told about the promo. I have only two cases and need to talk to the patients about it. I'm really interested."
"I have a LUMINEERS case coming up and called to order the Finishing Kit because of previous info I have seen on the CeriSaw and CeriSander."
"I read the info about CeriSaw and CeriSander and thought I would order them to do finsihing on LUMINEERS."
"Impressed that it was possible to revitalize old crowns and bridges."
"I have many patients this will help."
"I am very interested in the Revitalize Kit and the Porcelain Bonding of LUMINEERS."
"I saw the Revitalize ad, and am excited that I can offer treatment!"
"Assistant said, "I had called in with a question about protocol for bonding LUMINEERS. I was bonding to enamel but was using the Revitalize. Your staff went thought the entire procedure with me over the phone and I am very grateful. I am very glad that Den-Mat has trained staff to be available to help. Without Den-Mat's help I would have tried to do the procedure by myself. I would of likely not done a good job on the patient. Thank You."
"Staff said, " I saw a LUMINEERS ad in a beauty magazine over the weekend where it directed consumers to ask their dentist for a Revitalize Kit & I want to know what that is? The LUMINEERS ads are everyware and I want to be ready for patients to answer their questions."
"I have never seen any restoration look so perfect and natural! I would have done this years ago had I known about Revitalize."
" It turned out wonderful and Im not only pleased, but I have next case already booked with Cerinate Studios."
"I received info on the Revitalize Kit and wanted to know how I could get them free. Was told about the promo. I have only two cases and need to talk to the patients about it. I'm really interested."
"I have a LUMINEERS case coming up and called to order the Finishing Kit because of previous info I have seen on the CeriSaw and CeriSander."
"I read the info about CeriSaw and CeriSander and thought I would order them to do finsihing on LUMINEERS."
"Impressed that it was possible to revitalize old crowns and bridges."
"I have many patients this will help."
"I am very interested in the Revitalize Kit and the Porcelain Bonding of LUMINEERS."
"I saw the Revitalize ad, and am excited that I can offer treatment!"
"Assistant said, "I had called in with a question about protocol for bonding LUMINEERS. I was bonding to enamel but was using the Revitalize. Your staff went thought the entire procedure with me over the phone and I am very grateful. I am very glad that Den-Mat has trained staff to be available to help. Without Den-Mat's help I would have tried to do the procedure by myself. I would of likely not done a good job on the patient. Thank You."
"Staff said, " I saw a LUMINEERS ad in a beauty magazine over the weekend where it directed consumers to ask their dentist for a Revitalize Kit & I want to know what that is? The LUMINEERS ads are everyware and I want to be ready for patients to answer their questions."
